Keene

IR Commander Matrix

Overview

Setup
Connections
Configuration

- Options
- Factory Default
- Setup IR Codes
- Blast IR Codes
- Configuration
- Password
- Assign IP routing

Operation
Stand alone
Browser Control

Java Program
Java Software Program
IP_status
Learning IR Code Basic
Learning IR Code Adv
Learning IR Code Tips

Advanced
Macro commands
IP routing via macro
IR Translation & Routing via Learning Remote
UDP Port
Firmware Update
Dynamic DNS
Port Forwarding
RS232 Control
RS232 X10 Control
Shadowfile

Troubleshooting
Quick Checklist
Reset

Other
Optional Accessories
Third Party Software
Software Developers

Downloads
Firmware & Software

 

Last revised 12/3/12

Optional Accessories

INPUT COMPONENTS
Standard IR Receiver 36 - 40kHz suitable for most domestic equipment.
IRSR

Wide Band IR Receiver
, 20- 120kHz for more esoteric equipment.
IRWBR

Panel Mount IR Receiver 36-40kHz. A discrete option suitable for fitting into cabinets, studded walls, ceilings etc. Available in different finishes. Requires a 16mm diameter hole.
IRPMR (black)
IRPMRW (white)
IRPMRB (brass)
IRPMRC (chrome)

Standard IR Receiver wall plate. 36-40kHz suitable for most domestic equipment, built into a single gang faceplate
IRSP

Wideband IR Receiver
wall plate. 20-120kHz suitable for most esoteric equipment, built into a single gang faceplate
IRSPW

IR Link Cable that allows you to take the IR wand output from products such as the the IR Anywhere, C5QCA, IRBKIT, Powermid etc, and feed it directly into the IR receiver input on another Keene IR product. Length: 1.5m (3.5mm - 3.5mm tip & body only)
KLDE6M

Wand IR lead To feed the wand output from other IR extender equipment directly to the IR Commander wand input (2.5mm stereo jack plug to 3.5mm stereo jack plug 2.0m long). KLDE10M

IR Anywhere The IR Anywhere modules can be used as another input source across a local network or internet.
KIRA
KIRA128

Input Expansion Module. An optional input expansion module that allows allows up to four remote IR receivers to be connected via CAT5 cable.
IRC4A

OUTPUT COMPONENTS

Universal Wand. The Universal wand can either be equipment fascia or shelf mounted. 
IRUW

Low Power Wand. Can be attached directly to the equipment fascia or will work up to 4 metres away. Even when attached directly the equipment will still respond to external IR signals.
IRLPW

High Power Wand. Will operate equipment from up to 10 meters away. Can also be used in the IR Distribution Amp low power output sockets if required, but will then only perform as a low power emitter. Not suitable for one-to-one operation. IRHPW

Note: The IR Commander Matrix can support the use of high or low power wands in any output.

Side Firing Wand. A short range emitter for direct attachment to the equipment fascia. IRSFW

Dual Blinking Wands. The single jack plug drives two IR emitter wands. The emitters are extremely tiny (just 9mm across) and are supplied with double sided adhesive pads to affix directly to the equipment fascia. The emitters actually flash red as IR signal is emitted giving visual confirmation that the IR signal was received and transmitted correctly. IRDW

Output Expansion Module. An optional output expansion module that allows allows up to four remote IR emitter wands to be connected via CAT5 cable. For use with routed output number 1 only.
IRC4B


EXTENSION
Extension leads, 3.5mm stereo jack plug to 3.5mm stereo socket to be used on input or output as required. We've tested the input up to 10m and the output to 20m.
3m extension KLD40
5m extension KLD405
10m extension KLD4010

You can extend the input much further by using CAT5 cable and a pair of the KA175 adaptors